Hongqiang Zhang This email address is being protected from spambots. You need JavaScript enabled to view it.¹, Daming Li¹, Shan Luo¹, Minghao Jia¹, Zhongmou Sun¹, Yanqing Li¹, Zhu Zhen¹ and Xingye Zhang²

¹State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin University, Tianjin 300072, P.R. China
²CMA CGM Shipping Co., Ltd., Marseille 13000, France

REFERENCES

1. [1] Albertson, M. L., Y. B. Dai, R. A. Jensen, and H. Rouse (1950) Diffusion of submerged jets, Transcript of the A.S.C.E 115, 639664.
2. [2] Blaauw, H. G., and E. J. Kaa (1978) Erosion of Bottom and Sloping Banks Caused by the Screw Race of Manoeuvring Ships, Hydraulics Laboratory: Delft, Netherlands.
3. [3] Bergher, H., and K. Cederwall (1981) Propeller Erosion in Harbours, Hydraulics Laboratory: Stockholm, Sweden.
4. [4] Verhey, H. J. (1983) The stability of bottom and banks subjected to the velocities in the propeller jet behind ships, Proceedings of the 8th International Harbour Congress, Antwerp, Belgium.
5. [5] Fuehrer,M.,H. Pohl, and K. Romisch(1987) Propeller jet erosion and stability criteria for bottom protection of various constructions, Bulletin of the Permanent International Association of Navigation Congresses, Belgium.
6. [6] Stewart D. P. J. (1992) Characteristics of a Ships Screw Wash and the Influence of Quay Wall Proximity, Doctor’sThesis, Queen’s University of Belfast,Northern Ireland.
7. [7] Hamill, G. A., and H. T. Johnston (1993) The decay of maximumvelocity within the initial stages of a propeller wash, Journal of Hydraulic Research 31(5), 605 613. doi: 10.1080/00221689309498774
8. [8] Hashmi, H. N. (1993) Erosion of a Granular Bed at a Quay Wall by a Ship’s Screw Wash, Doctor’s thesis, Queen’s University of Belfast, Northern Ireland.
9. [9] Lam, W., G. A. Hamill, Y. C. Song, D. J. Robinsonb, and S. Raghunathan (2011) A review of the equations used to predict the velocity distribution within a ship’s propeller jet, Ocean Engineering 38(1), 110. doi: 10.1016/j.oceaneng.2010.10.016
10. [10] Fuehrer, M., and K. Romisch(1977) Effectsof modern ship traffic on islands and ocean waterways and their structures, P.I.A.N.C. 24th Congress, Leningrad, Soviet Union.
11. [11] Hamill, G. A. (1987) Characteristics of the Screw Wash of a Manoeuvring Ship and the Resulting Bed Scour, Doctor’s thesis, Queen’s University of Belfast, Northern Ireland.
12. [12] Lam, W. H., G. A. Hamill, D. J. Robinson, S. Raghunathan, and Y. C. Song (2012) Analysis of the 3D zone of flow establishment from a ship’s propeller, KSCE Journal of Civil Engineering 16(4), 465477. doi: 10.1007/s12205-012-1256-7
13. [13] Sui, H. T., and P. F. Li (2013) Dynamic Grid Engineering Simulation and Case of Actual Combat, Post & Telecom Press: Beijing, China. (in Chinese)
14. [14] Yu, Y. (2008) Introduced and Advanced Tutorial of Fluent, Beijing Institute of Technology Press: Beijing, China. (in Chinese)
15. [15] Versteegs, H. K., and W. Malalasekera, (1995) An Introduction to Computational Fluid Dynamics the Finite Volume Method, Prentice Hall: Essex, U.K.
16. [16] Soloff S. M., and R. J. Adrian (1997) Distortion compensation for generalized stereoscopic particle image velocimetry, Measurement Science and Technology 8(12), 1441–1454. doi: 10.1088/0957-0233/8/12/008
17. [17] Carlton, J. S. (1994) Marine Propellers and Propulsion, Butterworth Heinemann: London, U.K.
18. [18] Prosser, M. (1986) Propeller Induced Scour, B.H.R.A. Project, Report No. A01415, The Fluid Engineering Centre, Cranfield, U.K.
19. [19] McGarvey,J.A.(1996) TheInfluenceoftheRudder on the Hydrodynamics and the Resulting Bed Scour of a Ship’s Screw Wash, Doctor’s thesis, Queen’s University of Belfast, Northern Ireland.